EcoWater Series 2200 Uživatelský manuál

ELECTRICAL SUPPLY The water softener works on a 24 volt, To connect the transformer to the valve 50 Hz electric power supply. You must plug push the

, , ~ ,:' . : PR()GRIM'MING Your unit is now fully plumbed in and ready to If the unit is a Sensatronic 411, 418 or 426 programme. If the

ABOUT TIMETRONIC Your water softener has an advanced electronic mechanism which provides for superior features not available on conventional timecloc

oo II -""-L/LI su -1 o su PM To advance the hour display o o oo To set the required hour press the TIME & DAY button once.press the

SETTHETIME OF RECHARGE NOTE The display should now be steady and read the correct time and day of the week. Only the hour minute/separator will flash

0 n To change the instruction for n To set the instruction forY a Sunday press RECHARGE DAYSunclays to ON, press the SET/CLEAR button once. once again

II SET THE FILL CYCLE MINUTES The unit is factory set to 'fill the unit with water for 16 minutes to soak the salt and produce brine for recharge

TO RECHARGE NOW D Press and hold the ON/OFF .button until RCHG shows inAn automatic recharge can be initiated at the display.any time. If you have gue

POWER CUTS If electrical power to the timer is interrupted, the "memory" built into the timer circuitry keeps all settings for a minimum of

o ~ AS()UT SENSATR()NIC Your water softener has an advanced Sensatronic metering system which gives many product features and important savings on sa

INTRODUCTION Thank you for choosing a Permutit Water This User Manual will guide you through the Softener from EcoWater. steps of how to install yo

••n The unit will flash 00:00 after a few panel display a beeper sounds. One beepU seconds. signals that a change is accepted. If the beeper sounds co

••• SET THE WArER HARDNESS CALCULATION The display will flashg15 hardness" (this is a preset factory setting). The user guide on Page 35 indicate

••D SETTHE RECHARGE TIME The display will flash 02:00 recharge NOTE time which is the pre-set factory setting. 02:00 is chosen because hard water If y

CHECK THE SETTINGS Pressingthe SELECfbutton runsyou through the different stages of the programming. Press Select once Time will 'flash and show

•• n U To cancel recharge tonight, press the The display will return to the time display. RECHARGE BUTTON once and immediately release. CHARGE "

POWER CUTS Ifthe electricalpowertothewatersofteneris interrupted, the time display is blank, but the 'memory' built into the faceplate will

ADVANCED OPTION FOR SENSATRONIC MODELS This section provides instruction on how to enter the secondary functions of the Sensatronic programme. By ent

COUNTINGTHE DAYS OFOPERATION D Press select once. The unit will display a AND NUMBER OF RE·CHARGES counting meter. If water is passing through the uni

SETriNG AUrRES OR GALLON (US)MEASURE Press select. The display will flash the current Press (+) once to activate the litre count setting. The unit is

DISPLAY THE BACKWASH TIME Press select once. The display will flash the backwash for 7 minutes for maximum current setting. The unit is factory set to

UNIT EXPLOSION Notes 1. Remove all packaging and parts from inside the unit. 2. To remove valve cover for ease of installation follow the instructions

SERVICE Hard water enters from the back of the controller and flows down to the resin tank. As it flows down through the resin bed, the resin beads a

THE RE-CHARGE CYCLE A) FILL Water passes through the brine valve and into the brine tank. The fill water dissolves the stored salt to make brine solut

D) BACKWASH E) FAST RINSE Water enters the resin bed at the bottom and Water flows at afast rate, down through the flows upward loosening it and fluff

CLEANING WATER LEVEL Your unit may be cleaned with a damp cloth The water level will vary. Generally there will and detergent. Do not use bleaches, so

TIMETRONIC SENSATRONICSOLUTION /Jii~:iiji, . 1 1. Is there Salt in the Cabinet, 6inches of Salt is aminimum level 2. Is the Bypass closed and the inle

PAGE REF. 1. If yes-take no action1. Is ihe water soft 2. Reset the recharge days if incorrect2. Timetronic-Checkthatthedaysof 13 recharge are set or

411 UNIT DIMENSIONS (mm) MODEL A B C D E F G 307 643 555 515 380 455 55 300 311 643 555 515 380 455 55 300 643 555 515 380 455 55 300 418 822 735

DAYS OF RECHARGE AND FILL TIME Timetronic units and the accompanying fill times. These settings are for guidance only SETTINGS FOR llMETRONIC MODELS a

All Permutit Domestic Water Softeners are 5. Resetting the programmer when the fully covered by a one year parts and labour influent water hardness or

17 USlRl'H!~KHANDDV" tAOOiLS 301-3\\ rlnETRON/( MOQ1LS 411-418-426 SENSRTRON/C 7 5 @ 9 10.1 8 1 ~ 4 6 INSTALLATION KIT PARTS (j)(j) 13 PART

PLANNING & SITING THE INSTALLATION The installation of aPermutit water softener is relatively easy to carry out, but we recommend that this work

WATER SOFTENER TYPICAL INSTALLATION DIAGRAM (SOFTENER VIEWED FROM REAR) TO STORAGE TANK TRANSFORMER PLUG MAINS WATER C B A DRAIN HOSE FLEXIBLE HOS

PLUMBING Turn off the water supply at the incoming main and begin plumbing as per the installation on the previous page. FIT TH E BYPASS KIT Cut the r

-FIT THE INLET AND OUTLET ADAPTORS Remove the plastic plug from the outlet port on the water softener valve. Fit the '0' rings to the outer

-/ ~ INSTALL THE METER SENSOR (Sensatronic models only) The water meter assembles to the valve outlet fitting. Softened water passing through the mete